i've used Robins Shim kit and can vouch for its effectiveness. shimmed mine from .008" factory setting to the .0005" within the .001" TIR while getting the proper 8-12lbs of force....

I've been getting an occasional request for these, so I had some made using the RotorWay parts call out and procedures. https://i.ibb.co/ZpWcS2JW/20261026-113855.jpg

Or you can buy a shim kit from me robinwayparts@gmail.com www.robinwayparts.com 480-318-1229 I've made 10 sets of RW shim kits to put in stock for your hub shimming needs!

The adhesion works fine for the application over many years, can always apply additional adhesive if necessary. I wouldn't say that's a reason not to use the product. Also, as many...

This from Ai ..... Question .... Is this product ok for a Roto moulded fuel tanks on a helicopter No, 3M 4014 is not recommended for use directly on roto-molded fuel tanks on a hel...

Chris’s T. was at Jim’s last week and complained about his pedals becoming very stiff after being free for years. He disconnected things until he discovered it was in fact the ...

For the few who are needing to shim their hub plate to center the hub on the main shaft. This is something you will need to do at some point if you run your ship long enough. Peel ...

I told everyone I was getting them made, but I only ordered 4 sets for the 4 RW upgraded TR shaft drives. So no spare opposite hand TR pitch horns :rolleyes:

holy merry christmas! i see some extra pitch horns 😉

this is great!!! i would order this however i dont have a need, i have the older non belt drive main pulley and my slider ball has a grease zerk where this would have threaded. gre...

Bob St. Dennis and I colaborated on getting these made and in stock. Y https://i.ibb.co/GvJgbxvt/20261017-151820.jpg

Rotorway used 3M4014

here are the parts, there are 4 of us Aussies doing the upgrade https://i.ibb.co/xtKNM19s/20261021-181243.jpg https://i.ibb.co/23mKzY2W/20261021-181227.jpg https://i.ibb.co/0yxw00t...

this is how the TR attach cone is fitted, simply cut of the skin that protrudes past the last bulkhead. https://i.ibb.co/YTBctpQT/20261018-135711.jpg https://i.ibb.co/V01Nxzsw/2026...

https://i.ibb.co/0zrW3VQ/20261018-140525.jpg https://i.ibb.co/HTR7V5Gy/20261018-140915.jpg https://i.ibb.co/xtKNM19s/20261021-181243.jpg https://i.ibb.co/23mKzY2W/20261021-181227.j...

Opening offer, $1500.

I have a new Rotorway 162 main shaft, still in shipping crate for factory for sale. $3,000.0 or make a offer.  no shipping in the price, local pick up text me  Larry Hale 704-609...

i'll let someone else chime in what NGK plugs they have installed from rotorway in the later years, the NGK pn i shared was just the equivalent of the Bosch ones installed in mine.

Thanks for the help. The spark plugs installed are NGK BKR6E by the previous owner. The BCPR6ES-11 appears to be close to the same except the P designation is a projecting insulato...

i have this note on my spark plugs page. i cross referenced the original Bosch plugs i had PN(FR7DCX) with NGK's plugs PN (BCPR6ES-11) i was wanting to do some testing with Pulstar...