[Hank Rouland]

Long shot, but does anyone know the story behind the unfinished Exec 90 pictured? The current owner, Roman "Vio" Lazar in NJ says he bought it about 20 years ago through an advertisement. He thinks the builder was in the midwest, but he doesn't remember, and there were no builder's logs.

Weird story, sort of. Sadly, the general arc of "unfinished and neglected" does seem like a rather common story for Rotorway projects. I figured I'd reach out in case it stirred anyone's memories.

He never did anything with it, it's been overrun by rats, and he'd like to get rid of it. I'd like to build an Exec, and I'm interested in using this one essentially as a base kit, to be fully rebuilt.

[Lyle Swallows]

if i were to guess i would say about half of all rotorway kits delivered ended up flying... and most abandoned or handed down to people who didnt care for them... this was the state of mine as i got it and i am undergoing a full rebuild aswell. almost harder than if it were an original untampered kit...

[Homer Bell]

I currently have 3 machines that fall into this category, all in much better shape than this one. 2 actually fly, 1 that has been upgraded and only needs instruments put back in or a glass panel installed, builders choice.
This appears to be to be an early EXEC , see body panels and doghouse, but has a elastomeric rotor system. No telling what engine it might have or the condition of same.
Blades? Symmetrical or asymmetrical condition of same.? the frame is older, which means it would have to have a couple of tubes added probably the landing gear is probably early early design so you will need to decide if you wanted to upgrade that. Some experienced roadway person would need to inspect this machine and determine its condition. They’re really isn’t a lot of stuff there that anyone that wanted to build an up-to-date machine could use I’d say a realistic value of that is between five and $10,000 probably closer to five..

---

If the thing had a good set of asymmetrical blades if would be worth much more. But that would need to be determined. A set of symmetrical blades that were at least hot glued , could be used and I’d put a value of maybe $5k on a set of those.
What engine it has and it condition along with blades , is the big things that determine value. Unfortunately engines condition is going to be very hard to know unless it’s locked up, which is a strong possibility.

---

If the thing had a good set of asymmetrical blades if would be worth much more. But that would need to be determined. A set of symmetrical blades that were at least hot glued , could be used and I’d put a value of maybe $5k on a set of those.
What engine it has and it condition along with blades , is the big things that determine value. Unfortunately engines condition is going to be very hard to know unless it’s locked up, which is a strong possibility.

[Orv Neisingh]

It will take a lot of work and a lot of $$ to make this ship airworthy. If you love the build process and have the money it would be a good project but the value is not very high as it sits. I would say it would be worth around $5K as it sits. As Homer stated, asymmetrical rotor blades add value, the main shaft is most likely rusted and pitted so would need a new one and they are very hard to come by. If the engine is to be upgraded to current with dual ignition ($10,000-$34,000) then you would need to upgrade to the 35mm secondary ($4500) the cog drive ($8500) new main rotor shaft ($6500) just for starters. A new set of rotor blades can set you back around $12,000. You could be investing more into an upgrade than just buying a very nice presently flying 162f for around $65,000.

[Lyle Swallows]

my model i "barn found" was a 1999/2000 model 162F, never flown but mostly finished, then upgraded with the cogdrive, 35mm shaft, even a governor, yet i'm still nearly $20,000 USD into it with regards to upgrading instruments, refreshing belts/bearings that were way too old, upgrading skids, the tailboom needed work, i needed doors, and i'm still yet to paint it!

its gotta be a love and passion or hope you have nearly unlimited time and attention.

Homer is your best bet for a flying machine right off the bat, and this one would be good for parts or a frankenstein experiment in the future.

i hope you do continue and join our community!